Устройство кровли из асбестоцементных волнистых листов
По мере подхода фронта работ к инвентарной площадке первую секцию отсоединяют, переносят краном на противоположный конец пути и снова соединяют с последней секцией. Присоединенная секция до очередной перестановки будет являться основанием для приемной площадки, деревянные щиты которой также переносят. При новом приближении фронта работ демонтируют вторую секцию и т. д.
Для покрытия односкатных крыш зданий значительной длины необходимо иметь два однотипных крана. Первый из них устанавливают, как указано выше, а второй таким образом, чтобы вылет стрелы его (в плане) перекрывал рабочую зону первого,
Основным приспособлением для подъема и перенесения волнистых листов усиленного профиля является строп с жесткими захватами, шарнирно закрепленными в П-образной проушине. Захваты стропа делают различной длины, чтобы можно было переносить лист в наклонном положении. Для предупреждения изломов и выкрашивания асбестоцемента в торцах листа применяют резиновые наконечники (склеены из полосок старых автомобильных камер), которые натягивают на расплющенные концы жестких захватов.
Шарнирный строп состоит из двух пар стальных прутков, изогнутых и попарно сваренных посередине. Расплющенные концы сваренных захватов разнесены друг от друга на длину, равную четырем шагам волны (668 мм). Стропы захватывают лист с двух сторон, при этом их концы с эластичными наконечниками держат лист снизу за впадины волн.
Асбестоцементные волнистые листы усиленного профиля можно укладывать с подмостей. Подмости представляют собой тележку, металлическая рама которой установлена наклонно на четырех роликах. Благодаря роликам тележка свободно перемещается вдоль прогонов. Тележка имеет приспособление, обеспечивающее ей устойчивое положение на прогонах с уклоном до 25%- В центральной части тележки есть грузовая площадка, на которой укладывают стопу асбестоцементных листов (до 12 шт.). На узких концах тележки предусмотрены две площадки с ограждением рабочего места укладчиков. На площадке, расположенной в сторону карниза, находится звеньевой, а на противоположной — его подручный. Слева от площадки звеньевого установлен кран-укосина с захватом 6 для подъема и перенесения волнистого листа из стопы на прогоны. Тележка вместе со стопой листов (12 шт.) и двумя монтажниками весит 840 кг.
При монтаже с подмостей тележку устанавливают на втором и третьем прогонах с таким расчетом, чтобы звено кровельщиков могло покрывать одновременно два горизонтальных ряда (на рисунке карнизный ряд из листов ВУ-200-К и первый рядовой из листов ВУ-175-К).
Со своих мест на площадках монтажники приспособлением 6 захватывают из стопы один лист, краном-укосиной поднимают и переносят его в очередной ряд (на рисунке во второй), где опускают на прогоны и освобождают от захватов. После этого подручный с помощью лебедки переводит тележку на новую позицию (на ширину листа), и операцию повторяют сначала.
Крепление листа к прогонам выполняют те же монтажники, для чего они выходят со своих рабочих мест на покрытие. Если звено состоит из трех монтажников, то третий занимается только креплением листов.
Уложив в покрытие два горизонтальных ряда (карнизный и первый рядовой), тележку переносят монтажным краном на новую позицию и устанавливают ее на четвертом и пятом прогонах для монтажа очередных горизонтальных рядов — третьего (второй рядовой) и четвертого (третий рядовой).
Чтобы обеспечить листам, уложенным в покрытие, свободную усадку по ширине при суточных и сезонных колебаниях температуры на кровле, через каждые 6—12 м делают деформационные швы, которые позволяют листам смещаться и частично коробиться, а затем возвращаться в исходное положение.
Компенсационные швы делают путем нахлестки перекрываемого края одного листа перекрывающим краем смежного. Такая нахлестка должна гарантировать свободную сдвижку листов в поперечном направлении ряда на 25—30 мм. Чтобы вода не затекала на чердак, шов сверху закрывают асбестоцементными лотками Л1 или Л2, укладывая их последовательно в направлении снизу вверх. Лотки соединяют между собой внахлестку (на 200 мм) по стоку воды. С рядовыми листами лотки крепят специальными скобами.
В коньке листы покрытия обоих скатов опирают на продольные ребра конькового прогона. Каждый край ската закрывают асбестоцементными малыми переходными деталями. Отогнутые кверху края деталей покрывают сверху асбестоцементными коньковыми деталями. Малые переходные и коньковые детали сопрягают внахлестку и крепят на каждом скате с обеих сторон крючьями. Проходы крючьев через покрытие уплотняют водоизоляционными прокладками.
Постоянный ходовый мостик с ограждением вдоль конька устанавливают на переходных брусках, укрепляемых на покрытиях скатов.
Продольное примыкание кровли к парапету или стене осуществляют в такой последовательности. Край кровли из листов вводят в борозду, устраиваемую в стене. Затем этот край сверху закрывают в направлении снизу вверх неравнобокими угловыми деталями, которые вместе с листами усиленного профиля крепят к прогонам крючьями К1. Детали соединяют между собой внахлестку (на 200 мм) по стоку воды.